Eradicating a camper awning could be a daunting job, nevertheless it does not should be. With the precise instruments and somewhat endurance, you’ll be able to take away your awning rapidly and simply.
Earlier than you start, ensure you have all the mandatory instruments. You will want a ladder, a screwdriver, a wrench, and a pair of pliers. You may additionally wish to have a helper readily available to help you.
After you have gathered your instruments, start by eradicating the screws that maintain the awning arms to the camper. Subsequent, take away the bolts that maintain the awning curler to the camper. As soon as the bolts are eliminated, you’ll be able to fastidiously elevate the awning curler off the camper. Watch out to not harm the curler or the awning material.
Collect Needed Instruments and Supplies
To make sure a clean and environment friendly camper awning removing course of, it’s essential to collect the mandatory instruments and supplies beforehand. This is a complete record to information your preparation:
Instruments:
| Device | Objective |
|---|---|
| Adjustable Wrench or Socket Set | Loosening and tightening bolts and nuts |
| Phillips and Flathead Screwdriver Set | Eradicating screws that maintain awning elements in place |
| Utility Knife | Chopping awning material and cordage |
| Hammer | Tapping gently to launch caught elements |
| Pliers | Gripping and pulling material and cordage |
Supplies:
| Materials | Objective |
|---|---|
| Awning Cloth Cleaner | Cleansing awning material earlier than storage |
| UV Protectant Spray | Defending awning material from solar harm throughout storage |
| Awning Storage Case | Storing awning material and elements neatly and securely |
Retract and Safe the Awning
Observe these steps to retract and safe the awning as a part of the removing course of:
1. Retract the Awning
a. Be sure the awning arms are straight, parallel to the camper, and never angled outwards or inwards.
b. Slowly use the pull strap or swap to retract the awning.
c. Guarantee the material has rolled up evenly on the curler tube.
d. When totally retracted, safe it with a strap or bungee twine.
2. Safe the Awning
a. Examine the awning material for any tears, holes, or free seams. Restore any harm earlier than securing.
b. Fold the aspect flaps of the awning material in opposition to the curler tube, defending the material from flapping within the wind.
c. Wrap the top flaps of the awning material across the curler tube, overlapping them barely to maintain moisture out.
d. Safe the awning material to the curler tube utilizing Velcro straps or a wrap-around cowl.
e. Tighten any free bolts, nuts, or screws that maintain the awning in place.
3. Clear the Awning
a. Use a delicate material or sponge and a gentle cleaning soap resolution to wipe down the awning material.
b. Rinse totally with clear water and permit to dry.
c. Apply a UV protectant spray to assist stop fading and harm from the solar.
| Instruments and Supplies Wanted |
|---|
|
|
By following these steps, you’ll be able to retract and safe the camper awning correctly to guard it from harm throughout storage or transportation.
Take away the Truss Arms
The truss arms are the metallic rods that stretch from the awning curler to the highest of the awning. They help the burden of the awning and preserve it from sagging.
To take away the truss arms, you’ll need to:
- Find the truss arm mounting brackets on the aspect of the RV.
- Loosen the bolts that maintain the mounting brackets in place.
- Take away the truss arms from the mounting brackets.
- Repeat steps 1-3 for the opposite truss arm.
Suggestions for Eradicating the Truss Arms
* Watch out to not harm the awning material when you’re eradicating the truss arms.
* If the bolts are rusted or caught, you should use a penetrating oil to loosen them.
* In case you are having issue eradicating the truss arms, you’ll be able to contact a certified RV technician for help.
WARNING: Earlier than eradicating the truss arms, ensure that the awning is totally retracted. Failure to take action might end in severe harm or harm to the awning.
| Instruments Wanted |
|---|
| Socket wrench |
| Screwdriver |
| Penetrating oil (non-compulsory) |
Take away the Awning Curler
Eradicating the awning curler entails a couple of further steps:
- Assist the awning material: Loosen the material stress by winding within the awning about midway. It will cut back the burden on the curler.
- Disconnect the facility: If the awning is motorized, disconnect the facility supply on the electrical panel or circuit breaker.
- Take away the top caps: On both sides of the curler, you may discover finish caps that safe the material and curler. Take away these caps utilizing a screwdriver or wrench.
- Slide out the curler: With the top caps eliminated, now you can slide the curler out of the awning tube. Watch out to not harm the material or curler as you achieve this.
| Step | Motion |
|---|---|
| 1 | Loosen the material stress |
| 2 | Disconnect the facility (if motorized) |
| 3 | Take away the top caps |
| 4 | Slide out the curler |
Detach the Awning Cloth
Now that the awning arms are indifferent, you’ll be able to take away the awning material. Begin by unhooking the material from the curler tube. There are normally a number of hooks or clips that maintain the material in place. As soon as the material is unhooked, fastidiously roll it up and safe it with a strap or bungee twine.
Eradicating the Awning Cloth
| Step | Motion |
|---|---|
| 1 | Unhook the material from the curler tube. |
| 2 | Fastidiously roll up the material. |
| 3 | Safe the material with a strap or bungee twine. |
Take away the Fascia and Drip Rail
The fascia is the vertical trim piece that runs alongside the highest of the awning. It’s usually held in place by screws or bolts. The drip rail is the smaller trim piece that runs alongside the underside of the fascia. It’s usually held in place by screws or adhesive tape.
To take away the fascia and drip rail, observe these steps:
- Find the screws or bolts that maintain the fascia in place. These are usually situated alongside the highest fringe of the fascia.
- Take away the screws or bolts.
- Gently pry the fascia away from the RV. It might be useful to make use of a putty knife or different skinny object to assist pry the fascia free.
- As soon as the fascia is eliminated, you’ll be able to take away the drip rail. The drip rail is usually held in place by screws or adhesive tape.
- If the drip rail is held in place by screws, take away the screws.
- If the drip rail is held in place by adhesive tape, use a warmth gun or hair dryer to warmth the tape till it turns into delicate. As soon as the tape is delicate, you’ll be able to gently pry the drip rail away from the RV.
| Screw or Bolt Measurement | Amount | Location |
|---|---|---|
| 1/4″ x 1″ | 4 | High fringe of fascia |
| #8 x 1-1/2″ | 6 | Backside fringe of drip rail |
Seal the Opening
As soon as the awning is eliminated, the opening within the RV wall must be sealed to stop water and pests from getting into. This may be accomplished with quite a lot of supplies, together with silicone caulk, butyl tape, or a mix of each.
Supplies Wanted:
| Materials | Objective |
|---|---|
| Silicone caulk | Seals gaps and cracks |
| Butyl tape | Creates a weather-tight barrier |
| Caulk gun | Dispenses caulk |
| Butyl tape curler | Applies butyl tape evenly |
Steps:
1. Clear the opening across the perimeter of the awning tube.
2. Apply a bead of silicone caulk across the opening.
3. Roll out a strip of butyl tape over the caulk, guaranteeing it overlaps the caulk by no less than 1 inch on both sides.
4. Use a caulk gun to use a second bead of silicone caulk over the butyl tape.
5. Easy out the caulk utilizing a finger or a caulk ending device.
6. Permit the caulk to remedy in response to the producer’s directions.
7. Double-check the seal for any gaps or cracks, and apply further caulk or butyl tape as wanted.
Examine and Clear the Eliminated Elements
Examine the Cloth
Unfold the awning material and examine it totally for any harm, resembling tears, holes, or stains. When you discover any harm, mark it with a bit of tape or chalk so you’ll be able to restore it later.
Clear the Cloth
Use a light cleaning soap resolution and a delicate brush to wash the material. Keep away from utilizing harsh detergents or bleach, as these can harm the fabric. Rinse the material totally with clear water and permit it to air dry.
Examine the Body
Examine the awning body for any indicators of harm, resembling rust, corrosion, or bending. When you discover any harm, you will need to restore it earlier than reassembling the awning.
Clear the Body
Use a light cleaning soap resolution and a delicate brush to wash the body. Pay particular consideration to the areas the place the material attaches to the body, as these areas usually tend to accumulate filth and particles. Rinse the body totally with clear water and permit it to air dry.
Examine the Arms and Brackets
Examine the awning arms and brackets for any indicators of harm, resembling bent or damaged elements. When you discover any harm, you will need to substitute the affected elements earlier than reassembling the awning.
Clear the Arms and Brackets
Use a light cleaning soap resolution and a delicate brush to wash the arms and brackets. Pay particular consideration to the areas the place the arms connect to the body and the brackets connect to the RV, as these areas usually tend to accumulate filth and particles. Rinse the arms and brackets totally with clear water and permit them to air dry.
Examine the Drive Motor
In case your awning is supplied with a drive motor, examine the motor for any indicators of harm, resembling free connections or defective wiring. When you discover any harm, you will need to restore or substitute the motor earlier than reassembling the awning.
Clear the Drive Motor
Use a delicate material to wash the outside of the drive motor. Keep away from utilizing water or some other liquids, as these can harm the motor. If the motor is especially soiled, you should use a vacuum cleaner to take away any free filth and particles.
Lubricate Shifting Elements
Common lubrication is essential for sustaining the sleek operation of your camper awning. Making use of lubricant to the shifting elements helps cut back friction and prevents untimely put on or harm. This is an in depth information to lubricating the shifting elements of your camper awning:
Instruments and Supplies
| Merchandise | Amount |
|---|---|
| Silicone-based lubricant spray | 1 can |
| Clear material | 1 |
Steps
-
Clear the shifting elements: Begin by cleansing the awning’s arms, joints, and pulleys with a humid material to take away any filth or particles which will have gathered. Permit the elements to dry utterly earlier than lubricating.
-
Establish the lubrication factors: Find the shifting joints the place friction is prone to happen, such because the hinge factors of the awning arms and the pulleys that information the awning material.
-
Apply lubricant: Shake the lubricant can totally earlier than use. Spray a lightweight coat of lubricant onto every lubrication level, guaranteeing the lubricant penetrates the joints and pulleys. Keep away from over-lubricating, as this may entice filth and particles.
-
Wipe away extra: Use a clear material to wipe away any extra lubricant which will have dripped or leaked out. This helps stop filth from sticking to the lubricated elements.
-
Lubricate commonly: Repeat the lubrication course of each few months or extra often in case your awning is used often or uncovered to harsh climate situations. Common lubrication will lengthen the lifetime of your awning and preserve it working easily.
Reinstall the Awning
To reinstall the awning, merely reverse the removing steps.
.
1. Insert the other finish of the awning into the curler tube.
2. Roll up the awning and safe it with the strap or twine.
3. Align the awning tube with the mounting brackets and slide it into place.
4. Tighten the bolts or screws to safe the awning.
5. Connect the help arms to the awning tube and lengthen them outwards.
6. Regulate the help arms to degree the awning.
7. Connect the top caps to the awning tube.
8. Join the awning material to the help arms and safe it with the material clamps.
9. Roll out the awning and lengthen it to its desired size.
10. Prolong the awning legs to help the awning and alter the peak as wanted.
| Bolt/Screw Measurement | Tightening Torque |
|---|---|
| 1/4″ | 10-15 ft-lbs |
| 5/16″ | 15-20 ft-lbs |
| 3/8″ | 20-25 ft-lbs |
| 1/2″ | 25-30 ft-lbs |
How To Take away Camper Awning
Eradicating a camper awning could be a daunting job, nevertheless it’s really fairly easy if you happen to observe the steps beneath. First, you may want to collect your instruments. You will want a ladder, a socket wrench or drill, and a helper.
After you have your instruments, you can begin eradicating the awning. First, climb up the ladder and unhook the awning from the curler tube. Watch out to not drop the awning, as it may be heavy.
Subsequent, take away the bolts that maintain the curler tube to the camper. Make sure to help the curler tube as you take away the bolts, as it may be heavy.
As soon as the curler tube is eliminated, you’ll be able to take away the awning material. Begin by unhooking the material from the curler tube. Then, fold up the material and retailer it in a protected place.
Lastly, you’ll be able to take away the awning arms. Begin by eradicating the bolts that maintain the arms to the camper. Then, fastidiously take away the arms. Watch out to not harm the camper as you take away the arms.
Individuals Additionally Ask About How To Take away Camper Awning
How do you take away a slide out awning?
To take away a slide out awning, you may have to observe the steps beneath:
1. Retract the awning all the best way into the housing.
2. Unbolt the mounting brackets from the slide out.
3. Fastidiously elevate the awning straight up and off of the mounting brackets.
4. Retailer the awning in a protected place.
How do you take away a retractable awning?
To take away a retractable awning, you may have to observe the steps beneath:
1. Retract the awning all the best way into the housing.
2. Take away the screws that maintain the housing to the wall.
3. Fastidiously elevate the housing straight up and off of the wall.
4. Disconnect {the electrical} wires from the motor.
5. Retailer the awning in a protected place.
How do you take away a window awning?
To take away a window awning, you may have to observe the steps beneath:
1. Take away the screws that maintain the awning to the window body.
2. Fastidiously elevate the awning straight up and off of the window body.
3. Retailer the awning in a protected place.
