4 Easy Steps: How To Remove A Badger Garbage Disposal

4 Easy Steps: How To Remove A Badger Garbage Disposal

Badger rubbish disposals are a standard sight in lots of houses. They’re recognized for his or her sturdiness and effectivity, however even the most effective rubbish disposals can ultimately should be changed. In case you are contemplating eradicating a Badger rubbish disposal, there are some things it’s essential know. First, you have to to disconnect the ability to the disposal. This may be completed by turning off the breaker that provides energy to the kitchen. As soon as the ability is disconnected, you possibly can start to take away the disposal.

To take away the disposal, you have to to first take away the mounting bolts that maintain it in place. These bolts are usually situated on the underside of the disposal. As soon as the bolts are eliminated, you possibly can rigorously carry the disposal out of the sink. You’ll want to help the disposal along with your different hand as you carry it out. As soon as the disposal is out of the sink, you possibly can disconnect the drain line and the ability wire.

Now that the disposal is disconnected, you possibly can eliminate it. Most rubbish disposals may be disposed of within the trash. Nevertheless, chances are you’ll must verify along with your native waste administration firm to see if there are any particular disposal necessities. As soon as the disposal is disposed of, you possibly can set up a brand new one. To put in a brand new disposal, merely observe the directions that got here with the brand new unit. You’ll want to join the drain line and the ability wire earlier than turning on the ability to the brand new disposal.

Collect Important Instruments

Earlier than embarking on the duty of eradicating your Badger rubbish disposal, it’s essential to collect all the mandatory instruments to make sure a easy and secure course of. The next is a complete listing of important instruments you have to:

Wrench

An adjustable wrench is the first software for disconnecting the discharge tube and the mounting bolts that safe the disposal to the sink. Select a wrench with a snug grip and adequate leverage to loosen tight bolts.

Pliers

A pair of slip-joint pliers is important for eradicating {the electrical} wire connectors from the disposal’s motor. They supply a safe grip and forestall harm to the wires whereas disconnecting them.

Screwdriver

A screwdriver is required to take away the screws holding the dishwasher drain hose to the disposal’s dishwasher port. A Phillips head screwdriver is often used for this activity.

Bucket

A bucket is critical to gather any water or particles which will spill out throughout the elimination course of. It additionally offers a handy place to retailer the eliminated components quickly.

Flashlight

A flashlight is useful for illuminating the disposal’s underside and for reaching into tight areas throughout disassembly. It enhances visibility and permits you to work extra successfully.

Different Instruments

Further instruments that could be required for particular fashions or conditions embrace a putty knife, a flashlight, and a pair of gloves for hand safety. Getting ready with the suitable instruments will streamline the elimination course of and forestall delays because of lacking or insufficient instruments.

Disconnect the Energy Supply

To make sure your security throughout the elimination course of, it is essential to disconnect the ability supply out of your Badger rubbish disposal.

Establish the Energy Supply

Find {the electrical} outlet or circuit breaker that provides energy to your rubbish disposal. The outlet is often beneath the sink, whereas the circuit breaker is often in your house’s electrical panel.

Unplug the Outlet

In case your rubbish disposal is plugged into an outlet, merely unplug it. Use warning and keep away from touching the wires.

Flip Off the Circuit Breaker

In case your rubbish disposal is linked to a circuit breaker, find the corresponding breaker in your electrical panel. Flip the breaker to the “Off” place.

Energy Supply Kind Disconnection Methodology
Outlet Unplug the ability wire.
Circuit Breaker Flip the breaker to the “Off” place.

Entry the Disposal

1. Flip off the ability to the disposal. This may be completed on the circuit breaker or fuse field.

2. Open the cupboard doorways beneath the sink.

3. Find the disposal. It is going to be a cylindrical-shaped unit mounted beneath the sink. There shall be a big screw-on ring that holds the disposal in place.

4. Place a bucket or trash can beneath the disposal to catch any water or particles which will spill out.

5. Utilizing a screwdriver or wrench, loosen the screw-on ring that holds the disposal in place.

6. As soon as the ring is free, you possibly can pull the disposal down from the sink. Watch out, as it could be heavy.

Disconnect the Wiring

1. As soon as the disposal is faraway from the sink, you have to to disconnect the wiring. There shall be three wires which are linked to the disposal: a black wire, a white wire, and a inexperienced or naked copper wire.

2. Utilizing a pair of pliers, disconnect the black and white wires from the terminals on the disposal.

3. Disconnect the inexperienced or naked copper wire from the bottom screw on the disposal.

4. As soon as the wires are disconnected, you possibly can take away the disposal from the sink.

Disassemble the Splash Guard

To disassemble the splash guard, observe these steps:

1. Find the 2 tabs on the facet of the splash guard.
2. Insert a screwdriver or different skinny object into the slots on the tabs.
3. Push down on the tabs to launch the splash guard.
4. Rigorously carry the splash guard up and off the disposal.

Detailed Directions for Step 4:

When lifting the splash guard up and off the disposal, watch out to not harm {the electrical} wires linked to the disposal. These wires are situated on the underside of the splash guard and could also be simply broken if they don’t seem to be dealt with rigorously.

To keep away from damaging {the electrical} wires, observe these pointers:

  • Help the splash guard with one hand when you carry it up with the opposite.
  • Don’t pull on {the electrical} wires.
  • If {the electrical} wires are tangled, gently untangle them earlier than lifting the splash guard.
Step Description
1 Find the 2 tabs on the facet of the splash guard.
2 Insert a screwdriver or different skinny object into the slots on the tabs.
3 Push down on the tabs to launch the splash guard.
4 Rigorously carry the splash guard up and off the disposal.

Disconnect the Mount Ring

The mount ring is the steel ring that secures the rubbish disposal to the sink. To take away the Badger rubbish disposal, you first must disconnect the mount ring. This is do it:

  1. Flip off the ability to the rubbish disposal on the circuit breaker or fuse field.
  2. Unplug the rubbish disposal from the ability outlet.
  3. Place a bucket beneath the rubbish disposal to catch any water which will leak out.
  4. Use a wrench to loosen the bolts that safe the mount ring to the sink.
  5. Rigorously carry the rubbish disposal up and off the mount ring. Watch out to not harm the sink or the rubbish disposal.
Bolt Measurement Wrench Measurement
1/2 inch 12-inch adjustable wrench
5/8 inch 14-inch adjustable wrench
3/4 inch 16-inch adjustable wrench

Take away the Disposal Physique

Detach {the electrical} wiring.

Disconnect the drain hose by loosening the clamp and sliding it off rigorously to keep away from splashing.

Disconnect the dishwasher drain hose by unscrewing the becoming connecting it to the disposal.

Take away the mounting bracket.
– To do that, you have to to find the three or 4 screws that maintain the bracket in place and take away them.

Rigorously decrease the disposal by loosening the mounting screws and pulling it down.

Clear the sink flange space totally earlier than putting in the brand new disposal.

Take away the Mounting Bracket

To take away the mounting bracket, you may want a Phillips head screwdriver. Observe these steps:

  1. Find the 2 screws that maintain the mounting bracket to the sink flange. These screws are usually situated on the underside of the sink flange, close to the sting of the sink.
  2. Use the Phillips head screwdriver to take away the 2 screws.
  3. As soon as the screws are eliminated, the mounting bracket must be free. Now you can carry the mounting bracket away from the sink flange.
  4. If the mounting bracket is caught, chances are you’ll want to make use of a putty knife or a flathead screwdriver to pry it free.
  5. As soon as the mounting bracket is eliminated, now you can entry the rubbish disposal unit.
  6. Repeat the identical steps on the opposite facet of the mounting bracket to take away it utterly.
  7. As soon as the mounting bracket is eliminated, now you can entry {the electrical} wires, drain pipe, and water provide strains which are linked to the rubbish disposal unit.

Clear the Mounting Space

Earlier than eradicating the disposal, it is essential to scrub the mounting space totally. It will assist stop any particles or residue from entering into the brand new disposal and inflicting issues.

Supplies Wanted:

Merchandise Amount
Gentle cloths or rags 2-3
Clear water 1 bucket
White vinegar (optionally available) 1/2 cup
Delicate dish cleaning soap A couple of drops

Steps:

  1. Flip off the water provide: Find the shut-off valves beneath the sink and shut them.
  2. Unplug the disposal: Discover {the electrical} outlet the place the disposal is plugged in and disconnect it.
  3. Arrange your cleansing station: Fill a bucket with clear water and add a couple of drops of dish cleaning soap. If desired, you too can add 1/2 cup of white vinegar to assist take away odors.
  4. Wipe down the mounting space: Use a gentle material or rag dipped within the cleansing answer to wipe down the mounting bolts, the mounting plate, and the encompassing space.
  5. Rinse the realm: Dip a clear material or rag in clear water and rinse the mounting space totally.
  6. Dry the realm: Use a dry material or rag to totally dry the mounting space.
  7. Examine the mounting bolts: Examine the mounting bolts for any harm or rust. If any bolts are broken or rusted, they need to get replaced.
  8. Lubricate the mounting bolts (optionally available): To make it simpler to put in the brand new disposal, you possibly can apply a small quantity of petroleum jelly or silicone lubricant to the threads of the mounting bolts. You’ll want to solely use a small quantity and wipe off any extra.

Reinstall the Disposal

Now that you’ve the Badger rubbish disposal eliminated, it is time to reinstall it. When you’ve got {an electrical} outlet beneath your sink, plug within the new disposal. Should you don’t have an outlet, you have to to run a brand new circuit to your sink. As soon as the disposal is plugged in, you possibly can connect it to the sink drain utilizing the mounting bracket.

As soon as the disposal is mounted, you possibly can join the drain line to the disposal. The drain line is the pipe that carries the wastewater from the sink to the disposal. To attach the drain line, merely slide the drain line onto the disposal’s drain connection. If needed, you should use a screwdriver to tighten the drain line onto the disposal.

As soon as the drain line is linked, you possibly can activate the water provide to the sink. Examine for leaks across the disposal and the drain line. Should you discover any leaks, tighten the connections till the leaks cease.

Activate the disposal and let it run for a couple of minutes. It will assist to prime the disposal and make sure that it’s working correctly. If the disposal is just not working correctly, verify the circuit breaker to make sure that it isn’t tripped. If the circuit breaker is just not tripped, chances are you’ll must name a plumber that will help you troubleshoot the issue.

Restore Energy and Confirm Operation

1. Reset the Circuit Breaker or Substitute the Fuse

Find the circuit breaker or fuse field that controls the ability to the Badger rubbish disposal. If the breaker has tripped or the fuse has blown, reset or change it accordingly.

2. Examine for Free Connections

Tighten any free wire connections on the circuit breaker or fuse field, in addition to any connections contained in the Badger rubbish disposal itself.

3. Isolate the Disposal from the Sink

Disconnect the Badger rubbish disposal from the sink by unscrewing the mounting bracket that holds it in place.

4. Disconnect the Electrical Wires

Rigorously disconnect {the electrical} wires from the Badger rubbish disposal’s motor. Observe the place of every wire for reconnecting later.

5. Take away the Badger Rubbish Disposal

Raise the Badger rubbish disposal straight up and out of the sink gap, taking care to not harm the pipes or wiring.

6. Clear the Sink Gap

Totally clear the sink gap and take away any particles or obstructions which will have contributed to the disposal’s malfunction.

7. Set up the New Badger Rubbish Disposal

Insert the brand new Badger rubbish disposal into the sink gap and safe it with the mounting bracket.

8. Reconnect the Electrical Wires

Reconnect {the electrical} wires to the Badger rubbish disposal’s motor, guaranteeing that they’re correctly tightened.

9. Reinstall the Disposal into the Sink

Decrease the Badger rubbish disposal again into the sink gap and reconnect the mounting bracket.

10. Confirm Operation

Activate the Badger rubbish disposal and run water by it to make sure it’s working accurately. Examine for any leaks, uncommon noises, or vibrations.

How To Take away A Badger Rubbish Disposal

Eradicating a Badger rubbish disposal is a comparatively easy activity that may be accomplished in a couple of minutes with the proper instruments. Listed below are the steps on do it:

  1. Flip off the ability to the disposal. This may be completed on the circuit breaker or fuse field.
  2. Disconnect the water provide to the disposal. This may be completed by turning off the water valve beneath the sink.
  3. Loosen the mounting bolts. There are usually three or 4 mounting bolts that maintain the disposal in place. Use a wrench to loosen these bolts.
  4. Disconnect {the electrical} wires. There are usually two electrical wires that join the disposal to the ability supply. Use a screwdriver to disconnect these wires.
  5. Take away the disposal. As soon as the mounting bolts and electrical wires are disconnected, you possibly can take away the disposal from the sink. Watch out to not drop it, as it’s heavy.

Individuals Additionally Ask About How To Take away A Badger Rubbish Disposal

How do I take away theBadger rubbish disposal housing?

To take away the Badger rubbish disposal housing, you have to to disconnect the ability to the disposal, disconnect the water provide, and take away the mounting bolts. As soon as the mounting bolts are eliminated, you possibly can pull the housing straight as much as take away it.

How do I take away the Badger rubbish disposal motor?

To take away the Badger rubbish disposal motor, you have to to take away the housing first. As soon as the housing is eliminated, you will notice the motor. There are usually three or 4 bolts that maintain the motor in place. Use a wrench to loosen these bolts and take away the motor.

How do I take away the Badger rubbish disposal blades?

To take away the Badger rubbish disposal blades, you have to to take away the motor first. As soon as the motor is eliminated, you will notice the blades. There’s a single bolt that holds the blades in place. Use a wrench to loosen this bolt and take away the blades.