A bathe diverter valve is a plumbing fixture that lets you swap the move of water between your showerhead and bathtub faucet. In case your diverter valve just isn’t working correctly, it’s possible you’ll not have the ability to get the water to move the place you need it to. Fortuitously, fixing a bathe diverter valve is a comparatively easy job that may be accomplished in only a few minutes.
Step one is to determine the kind of diverter valve that you’ve. There are two essential kinds of diverter valves: push-button and pull-up. Push-button diverter valves are the most typical kind, and they’re sometimes discovered on showerheads which have a separate deal with for controlling the water temperature. Pull-up diverter valves are much less widespread, and they’re sometimes discovered on showerheads which have a single deal with for controlling each the water temperature and the move of water.
Upon getting recognized the kind of diverter valve that you’ve, you may start the restore course of. For push-button diverter valves, step one is to take away the button. This could normally be performed by merely pulling on the button. As soon as the button is eliminated, you will have to take away the diverter valve cartridge. The cartridge is usually held in place by a screw or a clip. As soon as the cartridge is eliminated, you may examine it for harm. If the cartridge is broken, you will have to switch it.
How To Repair A Bathe Diverter Valve
A bathe diverter valve is a plumbing fixture that lets you swap the move of water between your showerhead and tub spout. In case your diverter valve just isn’t working correctly, it’s possible you’ll not have the ability to get the water to move the place you need it to. On this article, we’ll present you how one can repair a bathe diverter valve so that you could get your bathe again up and operating very quickly.
Step 1: Collect your instruments
Earlier than you begin, you will have to collect just a few instruments. These embrace:
- Phillips screwdriver
- Flathead screwdriver
- Wrench
- Plumber’s putty
- New diverter valve (if essential)
Step 2: Flip off the water provide
Step one is to show off the water provide to your bathe. It will forestall any water from leaking out when you are engaged on the diverter valve.
Step 3: Take away the previous diverter valve
As soon as the water provide is turned off, you may take away the previous diverter valve. To do that, use a Phillips screwdriver to take away the screws which might be holding the valve in place. As soon as the screws are eliminated, you may pull the valve out of the wall.
Step 4: Set up the brand new diverter valve
If you’re changing the previous diverter valve with a brand new one, now could be the time to do it. To put in the brand new valve, merely insert it into the outlet within the wall and tighten the screws that maintain it in place.
Step 5: Apply plumber’s putty
Earlier than you reattach the diverter valve to the wall, you will have to use a bead of plumber’s putty across the base of the valve. It will assist to seal the valve and stop any water from leaking out.
Step 6: Reattach the diverter valve
Upon getting utilized the plumber’s putty, you may reattach the diverter valve to the wall. To do that, merely push the valve again into the outlet within the wall and tighten the screws that maintain it in place.
Step 7: Activate the water provide
As soon as the diverter valve is reattached, you may activate the water provide to your bathe. Verify for any leaks across the valve. If there are any leaks, it’s possible you’ll must tighten the screws that maintain the valve in place or apply extra plumber’s putty.
Folks Additionally Ask About How To Repair A Bathe Diverter Valve
How have you learnt if a bathe diverter valve is dangerous?
There are just a few indicators {that a} bathe diverter valve is dangerous. These embrace:
- Water leaking from the valve
- The valve is troublesome to show
- The valve doesn’t swap the move of water correctly
Can I repair a bathe diverter valve myself?
Sure, you may repair a bathe diverter valve your self. Nevertheless, you will need to be aware that this can be a plumbing restore, so in case you are not snug working with plumbing, it’s best to name a plumber.
How a lot does it price to repair a bathe diverter valve?
The associated fee to repair a bathe diverter valve will differ relying on the kind of valve you could have and the labor prices in your space. Nevertheless, you may anticipate to pay between $50 and $150 for elements and labor.
