Sustaining a clear dwelling atmosphere is important for each your well being and well-being. One essential facet of attaining that is guaranteeing that your Shark Flexstyle vacuum cleaner is working at its finest. Over time, nevertheless, grime, mud, and particles can accumulate in its filter, hindering its efficiency and probably affecting indoor air high quality. On this article, we’ll present a step-by-step information on learn how to clear the Shark Flexstyle filter successfully, restoring its performance and guaranteeing optimum air purification in your house.
Earlier than embarking on the cleansing course of, it is vital to assemble the mandatory supplies. You will want a vacuum cleaner with a hose attachment, a mushy brush or fabric, and a clear sink or bucket. Moreover, make sure that the vacuum cleaner is unplugged from the ability outlet for security causes. To start, take away the filter from the vacuum cleaner by urgent the discharge button positioned on the filter housing. As soon as the filter is indifferent, you possibly can proceed with the cleansing steps outlined beneath.
Firstly, use the vacuum cleaner hose attachment to softly take away any unfastened grime or particles from the filter. This can assist to dislodge any massive particles that will have gathered on the filter floor. Afterward, rinse the filter completely below operating water from the sink or bucket. Whereas rinsing, gently agitate the filter to loosen any remaining grime or grime. Keep away from utilizing harsh detergents or chemical compounds, as these might harm the filter materials. As soon as the filter is completely rinsed, shake it vigorously to take away extra water. Lastly, enable the filter to air dry utterly earlier than reinserting it again into the vacuum cleaner. By following these steps, you possibly can successfully clear the Shark Flexstyle filter, guaranteeing optimum efficiency and sustaining a wholesome dwelling atmosphere.
Figuring out the Filter Sort
Shark Flexstyle vacuums are geared up with two sorts of filters: the pre-motor filter and the HEPA filter. The pre-motor filter is positioned close to the brushroll, whereas the HEPA filter is positioned close to the exhaust port. It is essential to establish the proper filter kind to make sure environment friendly cleansing and optimum efficiency of your vacuum cleaner.
Pre-Motor Filter Identification:
The pre-motor filter is usually made of froth and is designed to seize bigger mud particles and particles earlier than they attain the motor. It’s normally positioned close to the brushroll, both contained in the dustbin or instantly behind it. To establish the pre-motor filter, confer with the vacuum’s consumer handbook or search for a foam filter part close to the brushroll space. Cleansing the pre-motor filter commonly is important to take care of the vacuum’s suction energy and forestall mud buildup throughout the motor.
| Pre-Motor Filter Location | Description |
|---|---|
| Contained in the dustbin | Foam filter positioned on the backside of the dustbin |
| Behind the brushroll | Foam filter located behind the rotating brushroll |
Eradicating the Filter
The Shark Flexstyle vacuum cleaner has a washable filter that must be cleaned commonly to take care of optimum suction energy. Here is a step-by-step information on learn how to take away the filter:
1. Detach the grime tank from the principle unit by urgent the discharge button and pulling straight up.
2. Open the grime tank by urgent the latch on the underside. The filter is positioned on the within of the tank.
3. To take away the filter, press the blue tab on the highest of the filter and pull it straight up. Watch out to not contact the filter materials.
Cleansing the Filter
The filter could be washed with heat water and a gentle detergent. Don’t use bleach or harsh chemical compounds. Rinse the filter completely and permit it to air dry utterly earlier than reattaching it to the grime tank.
Reattaching the Filter
As soon as the filter is dry, reattach it to the grime tank by inserting it into the slot on the within of the tank. Ensure that the filter is absolutely inserted and the blue tab is locked into place.
Reattach the grime tank to the principle unit and also you’re able to vacuum once more.
Here is a abstract of the steps in a desk format:
| Step | Motion |
|---|---|
| 1 | Detach the grime tank. |
| 2 | Open the grime tank. |
| 3 | Take away the filter by urgent the blue tab and pulling it straight up. |
| 4 | Rinse the filter completely with heat water and a gentle detergent. |
| 5 | Permit the filter to air dry utterly. |
| 6 | Reattach the filter to the grime tank. |
| 7 | Reattach the grime tank to the principle unit. |
Cleansing the Filter Foam
Take away the Filter Foam
Find the filter foam on the underside of the vacuum cleaner. Depress the discharge button and pull the filter foam straight as much as take away it.
Rinse the Filter Foam
Use chilly, operating water to rinse the filter foam completely. Keep away from utilizing scorching water, as this may harm the froth.
Squeeze Out Extra Water
Gently squeeze out any extra water from the filter foam. Don’t twist or wring the froth, as this may harm it.
Air Dry the Filter Foam
Place the filter foam in a well-ventilated space to air dry utterly. Keep away from putting the filter foam in direct daylight, as this may trigger it to turn into brittle.
Observe:
It is strongly recommended that you just clear the filter foam commonly to take care of optimum suction efficiency. The frequency of cleansing will differ relying on how usually you utilize your vacuum cleaner. If you happen to discover a lower in suction energy, it’s a good suggestion to test the filter foam and clear it if vital.
| Reccommended time for filter substitute |
|---|
| Month-to-month for heavy use |
| Bimonthly for average use |
| Quarterly for gentle use |
Cleansing the Felt Filter
The felt filter is positioned on the underside of the Shark Flexstyle vacuum cleaner. It’s chargeable for capturing wonderful mud and particles from the air. To wash the felt filter, observe these steps:
-
Unplug the vacuum cleaner from the ability outlet.
-
Take away the mud cup by urgent the discharge button on the highest of the vacuum cleaner.
-
Take away the felt filter from the underside of the mud cup.
-
Rinse the felt filter with chilly water till the water runs clear.
-
**GentlySqueeze Out Extra Water:
Upon getting rinsed the felt filter, gently squeeze out any extra water.
- Keep away from wringing or twisting the filter, as this may harm the fibers.
- Use a clear towel to soak up any remaining moisture.
- Permit the filter to air-dry utterly earlier than reinserting it into the vacuum cleaner.
-
Reinsert the felt filter into the underside of the mud cup.
-
Reattach the mud cup to the vacuum cleaner.
-
Plug the vacuum cleaner again into the ability outlet and resume use.
Resetting the Filter Indicator
Resetting the filter indicator is an easy course of that may be accomplished in just some steps. Observe these directions to reset the indicator:
Step 1: Find the Filter Reset Button
The filter reset button is positioned on the underside of the Shark Flexstyle vacuum cleaner. It’s a small, black button with a corresponding label. It’s positioned close to the dustbin launch button.
Step 2: Press and Maintain the Reset Button
Upon getting positioned the filter reset button, press and maintain it for roughly 5 seconds. The filter indicator gentle will start to flash.
Step 3: Launch the Reset Button
As soon as the filter indicator gentle has began flashing, launch the reset button. The sunshine will proceed to flash for a couple of extra seconds earlier than turning off.
Step 4: Exchange the Filter
As soon as the filter indicator gentle has turned off, you possibly can exchange the previous filter with a brand new one. You should definitely insert the brand new filter accurately, as indicated within the vacuum cleaner’s consumer handbook.
Step 5: Test the Filter Indicator
After changing the filter, test the filter indicator gentle to make sure that it has reset. The sunshine needs to be off, indicating that the filter is clear and able to use.
Step Motion 1 Find the Filter Reset Button 2 Press and Maintain the Reset Button for five Seconds 3 Launch the Reset Button 4 Exchange the Filter 5 Test the Filter Indicator The way to Clear Shark Flexstyle Filter
The Shark Flexstyle filter is a crucial a part of your vacuum cleaner, and it must be cleaned commonly to maintain your vacuum operating at its finest. Listed here are the steps on learn how to clear your Shark Flexstyle filter:
- Flip off and unplug the vacuum cleaner.
- Find the filter. The filter is positioned within the high of the vacuum cleaner, behind the dustbin.
- Take away the filter. To take away the filter, press the discharge button on the highest of the vacuum cleaner and pull the filter straight up.
- Clear the filter. You may clear the filter by rinsing it with water or by utilizing a vacuum cleaner to take away the mud and grime.
- Permit the filter to dry utterly. Earlier than you set the filter again within the vacuum cleaner, be sure that it’s utterly dry.
- Reinstall the filter. To reinstall the filter, merely push it again into place within the high of the vacuum cleaner.
- Plug in and activate the vacuum cleaner.
Your Shark Flexstyle filter is now clear and able to use.
Individuals Additionally Ask
How usually ought to I clear my Shark Flexstyle filter?
You must clear your Shark Flexstyle filter each 2-3 months, or extra usually in the event you vacuum ceaselessly.
Can I wash my Shark Flexstyle filter within the dishwasher?
No, you shouldn’t wash your Shark Flexstyle filter within the dishwasher. The dishwasher’s warmth and detergent can harm the filter.
The place can I purchase a substitute Shark Flexstyle filter?
You should purchase a substitute Shark Flexstyle filter at most main retailers, or on-line.
-
