Taking aside an Xbox 1 is usually a daunting job, nevertheless it’s truly fairly easy with the suitable instruments and directions. Whether or not you are seeking to improve your console’s {hardware}, repair an issue, or just clear it out, this information will stroll you thru the method step-by-step. Earlier than you start, it is essential to assemble the mandatory instruments: a T8 Torx screwdriver, a T10 Torx screwdriver, a Phillips #0 screwdriver, and a spudger. You will additionally want a clear, well-lit workspace.
First, you will have to take away the highest cowl of the Xbox One. To do that, use the T8 Torx screwdriver to take away the six screws positioned on the again of the console. As soon as the screws are eliminated, fastidiously raise the highest cowl off. Subsequent, you will have to take away the ability provide. To do that, use the T10 Torx screwdriver to take away the 4 screws positioned on the again of the ability provide. As soon as the screws are eliminated, fastidiously raise the ability provide out of the console.
Now you will have to take away the motherboard. To do that, use the Phillips #0 screwdriver to take away the 4 screws positioned on the highest of the motherboard. As soon as the screws are eliminated, fastidiously raise the motherboard out of the console. Lastly, you will have to take away the optical drive. To do that, use the spudger to softly pry the optical drive out of the console. As soon as the optical drive is eliminated, you will have efficiently taken aside your Xbox One.
Eradicating the Energy Provide Unit
To take away the ability provide unit (PSU), observe these steps:
1. Disconnect the Xbox One from the ability outlet and any HDMI or different cables.
2. Flip the Xbox One the other way up and find the PSU in the back of the console. There are two screws securing the PSU in place. Take away these screws utilizing a T9 Torx screwdriver.
| Step | Description |
|---|---|
| 1 | Take away the rear panel by urgent the discharge button on the high of the panel and sliding it up and off the console. |
| 2 | Disconnect the ability provide unit from the motherboard by unplugging the ability connector. |
| 3 | Take away the 2 screws securing the ability provide unit to the chassis and raise it out of the console. |
3. As soon as the PSU is eliminated, you may entry the motherboard and different inside parts of the Xbox One.
Disconnecting the Motherboard
After you have eliminated the again panel, you have to to disconnect the motherboard from the remainder of the console. It is a delicate course of, so you’ll want to take your time and watch out to not harm any of the parts.
Step 1: Disconnect the Energy Provide
Find the ability provide unit (PSU) in the back of the console. It’s a black field with a big fan. Disconnect the PSU from the motherboard by unplugging the ability connector.
Step 2: Disconnect the Optical Drive
The optical drive is positioned on the entrance of the console. It’s a black plastic tray that holds the disc. Disconnect the optical drive from the motherboard by unplugging the info and energy connectors.
Step 3: Disconnect the Arduous Drive
The onerous drive is positioned on the backside of the console. It’s a black metallic field. Disconnect the onerous drive from the motherboard by unplugging the info and energy connectors.
Step 4: Disconnect the Entrance Panel
The entrance panel is positioned on the entrance of the console. It comprises the ability button, the eject button, and the USB ports. Disconnect the entrance panel from the motherboard by unplugging the ribbon cable.
| Step | Description |
|---|---|
| 1 | Disconnect the ability provide |
| 2 | Disconnect the optical drive |
| 3 | Disconnect the onerous drive |
| 4 | Disconnect the entrance panel |
Extracting the Warmth Sink
To extract the warmth sink from the Xbox One, you will have to observe these steps:
- Disconnect the Energy Cable. Make sure the Xbox One is turned off and unplugged from the ability outlet.
- Take away Backside Cowl. Flip the console the other way up and take away the underside cowl utilizing a hex screwdriver.
- Unscrew Prime Outer Screws. Use a T10 Torx screwdriver to take away the three outer screws on the highest of the console.
- Take away Prime Cowl. Carry the highest cowl straight as much as take away it.
- Extract Warmth Sink. The warmth sink is positioned within the middle of the console, secured by 4 T10 Torx screws.
Steps Particulars a. Disconnect the fan connector from the warmth sink. b. Take away the 2 outer screws on either side of the warmth sink. c. Grip the warmth sink firmly and gently raise it straight as much as take away it from the console.
Dismantling the Controller
1. Take away the Battery Cowl
Slide the battery cowl positioned on the again of the controller towards the underside. The duvet ought to come off simply.
2. Take away the Batteries
As soon as the battery cowl is eliminated, you will notice the 2 AA batteries inside. Take away the batteries by gently pulling them out.
3. Take away the Facet Panels
Find the 4 screws holding the aspect panels in place. Two screws are on either side of the controller. Use a small screwdriver (T8) to take away all 4 screws.
4. Pry Open the Facet Panels
Insert a plastic opening software or a small flathead screwdriver into the seam between the aspect panel and the controller physique. Pry open the aspect panel fastidiously to keep away from breaking the clips.
5. Take away the Rumble Motors
The rumble motors are positioned contained in the aspect panels. Gently pull the rumble motors out of their slots.
6. Unplug the Management Module
The management module is the principle circuit board contained in the controller. It’s the rectangular board linked to the buttons and triggers. Unplug the management module by gently pulling it upwards till it disconnects.
7. Take away the Set off Buttons
Flip the controller over and find the 2 set off buttons on the again. There’s a small, plastic lug on the within of every set off button that matches right into a notch on the controller physique. Use a small Phillips screwdriver to softly push the set off buttons out from the within. Watch out to not harm the wires linked to the set off buttons.
| Step | Motion |
| — | — |
| 1 | Take away the battery cowl |
| 2 | Take away the batteries |
| 3 | Take away the aspect panels |
| 4 | Pry open the aspect panels |
| 5 | Take away the rumble motors |
| 6 | Unplug the management module |
| 7 | Take away the set off buttons |
Cleansing and Inspecting Inner Elements
After you have eliminated the entire exterior screws and parts, it is possible for you to to entry the inner parts of your Xbox One. The very first thing it is best to do is to unplug the ability twine and another cables which are linked to the console. As soon as the console is disconnected, you can begin to scrub the inner parts.
Cleansing the Inner Elements
The easiest way to scrub the inner parts of your Xbox One is to make use of a delicate, dry fabric. You can too use a can of compressed air to blow out any mud or particles which will have collected contained in the console.
Inspecting the Inner Elements
After you will have cleaned the inner parts, it is best to examine them for any harm. Search for any unfastened connections, damaged wires, or broken parts. If you happen to discover any harm, it is best to exchange the affected parts earlier than reassembling the console.
Checking Connections
Be sure that the entire inside parts are correctly linked to the motherboard. You should use a flashlight that will help you see contained in the console and ensure that the entire cables are securely plugged in.
Cleansing the Fan
The fan is liable for cooling the inner parts of your Xbox One. Over time, the fan can develop into clogged with mud and particles, which may cut back its effectiveness. To scrub the fan, you should use a delicate, dry fabric or a can of compressed air. Watch out to not harm the fan blades when cleansing them.
Checking the Arduous Drive
The onerous drive is the storage gadget in your Xbox One. If the onerous drive fails, you’ll lose your whole saved video games and different information. To verify the onerous drive, you should use the Xbox One’s built-in diagnostics software. To entry the diagnostics software, go to Settings > System > Console Data & Updates > Troubleshoot. Choose “Test for Updates” after which observe the on-screen directions.
Reassembling the Console
After you have cleaned and inspected the inner parts, you may reassemble the console. To reassemble the console, merely observe the steps in reverse order. Watch out to not overtighten the screws when reassembling the console.
The way to Take Xbox One Aside
Taking aside an Xbox One is usually a daunting job, nevertheless it’s not as troublesome as it might appear. With the suitable instruments and a bit endurance, you may have your Xbox One disassembled very quickly.
Listed below are the steps on easy methods to take Xbox One aside:
- Energy down the Xbox One and unplug it from the ability outlet.
- Take away the screws from the again of the Xbox One. There are 4 screws that maintain the again panel in place.
- Slide the again panel off the Xbox One. The again panel ought to slide off simply as soon as the screws are eliminated.
- Take away the screws that maintain the ability provide in place. There are 4 screws that maintain the ability provide in place.
- Disconnect the ability provide from the Xbox One. The ability provide is linked to the Xbox One by a cable. Merely unplug the cable to disconnect the ability provide.
- Take away the ability provide from the Xbox One. The ability provide ought to raise out simply as soon as it’s disconnected.
- Take away the screws that maintain the motherboard in place. There are 4 screws that maintain the motherboard in place.
- Carry the motherboard out of the Xbox One. The motherboard ought to raise out simply as soon as the screws are eliminated.
- Disconnect the cables which are linked to the motherboard. There are a number of cables which are linked to the motherboard. Merely unplug the cables to disconnect them.
- Take away the motherboard from the Xbox One. The motherboard ought to now be utterly disconnected from the Xbox One.
Individuals Additionally Ask About The way to Take Xbox One Aside
How do I take away the onerous drive from an Xbox One?
To take away the onerous drive from an Xbox One, you have to to:
- Take away the again panel of the Xbox One.
- Find the onerous drive bay. The onerous drive bay is positioned on the left aspect of the Xbox One, behind the ability provide.
- Press the discharge button on the onerous drive bay. The discharge button is positioned on the entrance of the onerous drive bay.
- Pull the onerous drive out of the onerous drive bay. The onerous drive ought to slide out simply as soon as the discharge button is pressed.
How do I exchange the thermal paste on an Xbox One?
To interchange the thermal paste on an Xbox One, you have to to:
- Take away the highest panel of the Xbox One.
- Take away the heatsink from the Xbox One. The heatsink is positioned on the highest of the Xbox One, behind the fan.
- Clear the previous thermal paste from the CPU and heatsink. You should use a cotton swab dipped in isopropyl alcohol to scrub the thermal paste.
- Apply new thermal paste to the CPU. Use a small quantity of thermal paste and apply it evenly to the floor of the CPU.
- Change the heatsink on the Xbox One.
- Change the highest panel of the Xbox One.
How do I clear the fan on an Xbox One?
To scrub the fan on an Xbox One, you have to to:
- Take away the again panel of the Xbox One.
- Find the fan. The fan is positioned on the again of the Xbox One, subsequent to the ability provide.
- Use a cotton swab dipped in isopropyl alcohol to scrub the fan blades.
- Use a can of compressed air to blow away any mud or particles from the fan.
- Change the again panel of the Xbox One.
